Unidrain - sita 13

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Toothbrush holder with a focus on hygiene. With a two-part insert, where one compartment holds the toothpaste tube in place, while the other is for the toothbrushes. The design ensures that the toothbrushes do not touch each other. The insert can be easily removed during cleaning. Non-slip surface.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

10-mm tempered glass.The surface is treated with GEWE-clean® nanotechnology, so that the shower screen can be right- or left-aligned.No visible screws and fittings in the finished result.The solution fits tile thicknesses up to 15 mm for wall tiles and up to 20 mm for floor tiles.

Horizontal outlet in Ø 32 mm.

Cannot be used with any type of water trap.

Only used as a secondary floor drain.

Can be turned 180˚ if a rear-facing outlet is required.

Lubricant for rubber seals is included.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Toothbrush holder with a focus on hygiene. With a two-part insert, where one compartment holds the toothpaste tube in place, while the other is for the toothbrushes. The design ensures that the toothbrushes do not touch each other. The insert can be easily removed during cleaning. Non-slip surface.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Complete drain system with corner unit and Custom base. The unit has been updated for easier installation. Note: the drain unit fits only the HighLine Custom solution.

Attach the tile to the custom base using the glue supplied. Use the included spacers to position the base and tile correctly.

The vinyl set comprises a magnetic unit, frame and grating. For shower cubicles without fixed walls.

The soap dispenser has a sturdy and elegant wall mounting. The design of the pump top ensures liquid soap is released wherever the pressure is applied. Oblique soap dispenser. The entire pump top can be removed to allow for cleaning and refilling. Instructions, screws and dowels are included. Content: 200 ml.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Meets capacity and self-cleaning requirements according to EN 1253 (the pan-European standard for floor drains) and is VA-approved. The water trap can easily be removed from the outlet unit using the mounted hook. Then dismantle and clean the water trap.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Water trap for corner outlet houses 2001.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

For shower cubicles with open left-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open left-hand side, glass screen or similar.

The drain unit has two wall flanges.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.