Has an automatic odour barrier instead of a water trap, so that it cannot dry out. The odour barrier can be removed for cleaning. VA-approved.

– Should not be used in multi-storey buildings
– The odour barrier may react to over-pressure and under-pressure in the drain system
– Correct ventilation of the drain system is important
– The odour barrier opens and closes with the help of a spring
– A rubber seal ensures that the odour barrier is closed when not in use

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Choose between two models. A panel completely without frame, or the model with panel including frame.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Complete floor drain against rear wall 900 mm, 10 mm frame, Column grate, 75 mm vertical outlet housing

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Choose between two models. A panel completely without frame, or the model with panel including frame.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time.

Combine with: Outlet unit, frame, grating/panel and shower screen.