Self-cleaning trap with a capacity of 0.4-0.6 l/s depending on the outlet unit it is installed in. Meets the requirements for capacity and self-cleaning according to EN1253 (the pan-European standard for floor drains) and is VA approved. Suitable for most outlet units, including older models. Can replace water trap 1820.0010 and 1820.0040, if they are installed at the top of the drain unit. A hook to lift the water trap up from the outlet unit and a packet of silicone lubricant are included

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

Meets capacity and self-cleaning requirements according to EN 1253 (the panEuropean standard for floor drains) and is VA-approved.

The water trap can easily be removed from the outlet unit using the mounted hook. Then dismantle and clean the water trap.

The set consists of the Custom base, rail, heightener set and screws.

The set must be assembled before installation.

Glue your own floor tile to the base, to complete the solution.

The Custom solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit.

Special glue for adhesion of your own tile and 10 x 6-mm spacers to use for installation are also included.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

Complete square drain set. Package includes HighLine Custom base 10×10 cm, steel drain unit, water trap, outlet unit Ø 75 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Special adhesive is included to glue your own tile to the Custom base. Hook and cleaning cloth included.

Soap shelf including grating and mounting set. Designed for insertion in tile joint or for mounting in an existing shower cubicle. For corner installation only – applies to both models.

For Shower cubicles with three fixed walls.

The drain unit has three wall flanges.

Bin bags for Reframe pedal bin. 10 rolls of 25 bin bags. Black plastic (PEHD). 2 pcs. specially designed tape for easy fitting of the bag are included. Volume 4 l.

Simple and easy day-to-day maintenance of floor drain.

The strainer is placed on top of the built-in water trap / odor barrier.

Prevents the water trap from becoming clogged.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of the Custom base, rail, heightener set and screws.

The set must be assembled before installation.

Glue your own floor tile to the base, to complete the solution.

The Custom solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit.

Special glue for adhesion of your own tile and 10 x 6-mm spacers to use for installation are also included.

Complete square drain set. Package includes ClassicLine Column grating and frame 10×10 cm, steel drain unit, water trap, outlet unit Ø 75 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Truncate the ClassicLine frame to tile level. Minimum tile layer 4 mm. Cleaning cloth included.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Has an automatic odour barrier instead of a water trap, so that it cannot dry out.

Can be removed for cleaning. VA-approved.

– SHOULD NOT BE USED IN MULTI-STOREY BUILDINGS
– Can react to the over- and under-pressure in the drainage system
– Correct venting of the drain system is therefore important, so that the odour barrier functions correctly
– Opens and closes with the help of a spring
– A rubber seal ensures that the odour barrier is closed when not in used

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Meets capacity and self-cleaning requirements according to EN 1253 (the pan-European standard for floor drains) and is VA-approved.

The water trap can be removed from the outlet unit and then dismantled for cleaning.

Complete square drain set. Package includes HighLine Custom base 10×10 cm, steel drain unit, flow guide, water trap, outlet unit Ø 110 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Special adhesive is included to glue your own tile to the custom base. Hook and cleaning cloth included.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Unidrain o-ring for water trap.

GlassLine - fixed module - left-side shower wall: W 900 mm, D 900 mm. GlassLine fixed module is a U-shaped module, with a floor drain as the middle long, a rail with tracks for placement of the shower wall as right/left long, and a rail for fixed mounting on the wall on the last long. All the way around, there are horizontal/vertical flanges that, together with the overlapping wet room membrane, ensure a 100% tight installation.The fixed module has two floor levels: On the inside of the shower wall, a 2% drop is built into the module, so the concrete can easily be pulled off and get the correct drop, on the outside of the shower wall, the rail is level, so it is easy to work further with the rest of the bathroom floor.The fixed module is available in different dimensions, and is combined with a shower wall, outlet housing, frame and grate/panel. You can choose between both ClassicLine and HighLine solutions.

The soap dispenser has a stable non-slip base. The design of the pump top ensures liquid soap is released wherever the pressure is applied. Oblique soap dispenser. The entire pump top can be removed to allow for cleaning and refilling. Instructions are included. Content: 200 ml.