Unidrain - sita 11

The set consists of the Custom base, rail, heightener set and screws.

The set must be assembled before installation.

Glue your own floor tile to the base, to complete the solution.

The Custom solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit.

Special glue for adhesion of your own tile and 10 x 6-mm spacers to use for installation are also included.

Ensures correct positioning and fixing of the drain unit in wooden floor joist structures. Adjust to the correct length by cutting the front profile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Hook to lift the water trap up from the outlet unit.Suitable for use with line and corner models.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

The soap dispenser has a stable non-slip base. The design of the pump top ensures liquid soap is released wherever the pressure is applied. Oblique soap dispenser. The entire pump top can be removed to allow for cleaning and refilling. Instructions are included. Content: 200 ml.

The soap dispenser has a sturdy and elegant wall mounting. The design of the pump top ensures liquid soap is released wherever the pressure is applied. Oblique soap dispenser. The entire pump top can be removed to allow for cleaning and refilling. Instructions, screws and dowels are included. Content: 200 ml.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Shelf of reinforced steel plate. Thin grooves lead the water away, and an anti-slip barrier keeps things in place. Smart bracket solution allows the shelf to be adjusted to corners that are not angled at exactly 90°.

Screws are included.

Water trap 50 mm water seal. Meets capacity and selfcleaning requirements according to EN 1253 (the panEuropean standard for floor drains) and is VA-approved. The water trap can be removed from the outlet unit and then dismantled for cleaning.

NOTE: Suitable only for outlet unit 1418.0050.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Available in 8/10/12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions:

To support the grating and give a perfectly flush finish with the tiled floor. NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8/10/12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions:

To support the grating and give a perfectly flush finish with the tiled floor. NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Horizontal drain, Ø 75 mm.

Including removable water trap that can be dismantle for cleaning.

Can be turned in all directions, to simplify pipework.

GlassLine - fixed module - left-side shower wall: W 900 mm, D 900 mm. GlassLine fixed module is a U-shaped module, with a floor drain as the middle long, a rail with tracks for placement of the shower wall as right/left long, and a rail for fixed mounting on the wall on the last long. All the way around, there are horizontal/vertical flanges that, together with the overlapping wet room membrane, ensure a 100% tight installation.The fixed module has two floor levels: On the inside of the shower wall, a 2% drop is built into the module, so the concrete can easily be pulled off and get the correct drop, on the outside of the shower wall, the rail is level, so it is easy to work further with the rest of the bathroom floor.The fixed module is available in different dimensions, and is combined with a shower wall, outlet housing, frame and grate/panel. You can choose between both ClassicLine and HighLine solutions.

Horizontal drain, Ø 75 mm.

Including removable water trap that can be dismantled for cleaning.

Can be rotated 180° if a rearfacing outlet is required.

Outlet housing, 1415.0050, Ø 50 mm horizontal side outlet, including trap. Product description: Outlet housing - line - Ø 50 mm horizontal side outlet, including trap. The outlet housing has a side outlet and an extra low installation height with high capacity. A locking bracket ensures that the outlet housing always sits securely in the correct position on the drain fitting. The trap is included and has a handle on top for easy removal and cleaning.