Intelligenta bygginstallationer

Operating tool with partially insulated shaft, blade (3.5 x 0.5) mm, short, suitable for 260, 261, 262, 264, 270, 280, 281, 869, 870 and 880 Series,

Operating tool with partially insulated shaft, blade (3.5 x 0.5) mm, short, angled, particularly suitable for 280 Series actuator and sensor terminal blocks and also for Series 260, 261, 262, 264, 280, 281, 869, 870, 880, 2002,,

The connected controller is the central module of every Niko Home Control installation. It covers all basic functions on which a Niko Home Control installation is built: it provides the power supply to the bus, ensures the connection with Niko Home Control IP devices (touchscreens and external video units) and enables remote control with a smartphone or tablet. Per installation only one connected controller is necessary. This module contains firmware that can only be programmed with the Niko Home Control programming software 2.1.1 or higher.

IHC Control Output 400 V AC 8X10A with 8 outputs. Used for coupling of 8 pieces. 230 V a.c. loads controlled by IHC system.

ABB KNX DALI-Gateway, Basic, 2-foldFor controlling DALI devices via ABB i-bus®. Two DALI outputs. Max. 2x64 DALI slaves (incl. emergency devices acc. EN 62386-202). Status feedback a control happens via KNX per DALI slave, group, Broadcast. Szene-, slave-, staircase-, force and block-fct.

· Maximum load of 6A/250 V· Loop terminals· Relay status via LED· Small dimensions

Product: PD4-S-DALI-P (92759) Presence detector LUXOMAT® PD4-S-DALI-P for surface mounting on the ceiling. DALI slave sensor which is used with the master: PD4-M-DAA4G. Detection range: 360 ° Range (around) m: - sitting Ø 6.40 m - across Ø 24.00 m - head Ø 8.00 m.

Perfect for retrofit arrangements.Make use of a room’s existingwall panel with our DALIcompatible power supply andinput unit.(331+407+444)

This module must always be positioned as the first module on the left at the beginning of a new row of DIN rail modules. The power supply and the bus are connected to the previous rail and/or to the next rail from the rail coupling or power supply module via the contacts on the top and bottom sides.

Single push button.

adhesive pad softline - wireless - 1 module - silver

Product: PD4-M-DAA4G-P (92743) Presence detector LUXOMAT® PD4-M-DAA4G-P for surface mounting on the ceiling, with four DALI zones + 1 voltage-channel, three low-voltage switches, only one DALI bus to all four DALI zones. Up to 64 DALI ballasts can be connected. Detection range: 360 ° Range (around) m: - sitting Ø 6.40 m - across Ø 24.00 m - head Ø 8.00 m

Product: PD4-M-DAA4G-i (92591) Presence detector LUXOMAT® PD4-M-DAA4G-i for recessed ceiling, with four DALI zones + 1 voltage-channel, three low-voltage switches, only one DALI bus to all four DALI zones, up to 64 coils can be connected. Detection range: 360 ° Range (around) m: - sitting Ø 6.40 m - across Ø 24.00 m - head Ø 8.00 m

Single flush surround plate from the range Niko Intense. Finishing colour flush surround plate: Intense white.

ABB KNX IP router connects the KNX bus with the Ethernet network. The device uses the KNXnet/IP protocol for communication (Routing and Tunneling).It can be used as a fast line and area coupler. The full filter table for main groups 0-31 is supported.KNX devices can be programmed via the LAN using ETS. For this and further clients 5 Tunneling Server are available.DIN 90X36X64 mm (H x W x D)The IP address can be fixed or can be received from a DHCP server. Power supply via 12..30 V DC or PoE.The KNX Standard Communication (Multicast) can be switched off. In this case, up to 10 IPR/S3.1.1 can communicate using unicast communication.

Digital black is a completely customisable control screen for Niko Home Control with an extremely user-friendly interface featuring clear symbols. The screen is automatically activated when your hand comes near. That way, you can switch or dim your lights, set scenarios, set ventilation modes, adjust blinds and sun blinds to the wanted position, in one operation. In short, all possible Niko Home Control control types are available.

Used with presence detectors 41-75x, 41-76x and 41-78x DALI

Fully DALI compatible Power Supply UnitProvides a DIGIDIM system with the required supply of up to 250 mAStatus LEDDALI short circuit and over temperature protectedDIN-rail mounted

IHC Control input 24 V DC 3mA with 16 inputs. Used to collect the signals from the low-current contacts with low contact resistance, for example. alarm PIR, thermostats, magnetic switches and other signal generators with long lasting finish functions. Note! OPUS / FUGA PIR can not be used for this input module. To IHC system can be considered a low voltage system, it is a requirement that the used switches are insulated to double insulation (8 mm creepage distance) relative to the 230 / 400V network. It is possible to place the input module 24/3 both central controller and by a decentralized, distributed in the installation.

· 230 V AC· Flush mounted in the ceiling· Use together with Master type 41-65x· Extends the detection area to all Masters type 41-65x· Plug & Play - no programming· Rapid and flexible installation with DALI addressable bus· Supply voltage via the DALI bus· Standby consumption < 0,1 W· Prodtection class IP20

ABB 6131/31-24-500 Vit Plast

Interface, RS RJ45, RJ45 plug-in connectors, 8-pole, Screw connection

Wide motion detection range DALI multisensorSeemless integration in DALI single-room solution B.E.G. LUXOMAT®net DALI LINK as modular multimaster option for lighting controlMultimaster-capable with slave functionMixed light measurement with internal and external light sensorSemi-automatic, full-automatic or twilight switch modeIntegrated daylight harvesting circuit (or switch output)Guided Light, Soft-Start PLUS, Orientation light PLUSWorks out-of-the box for easy installation checkFull range of functions can only be activated with other products of the product group B.E.G. LUXOMAT®net DALI LINKDetection area can be restricted with blindsApplication examples:monitoring of large areas, warehouses, loading ramps, underground car parks, gyms, halls.

Used with presence detectors 41-75x, 41-76x and 41-78x DALI

For controlling DALI devices via ABB i-bus®. One DALI output. Max. 64 DALI slaves (incl. emergency devices acc. EN 62386-202). Status feedback and control happens via KNX per DALI slave, group or broadcast. Szene-, slave-, staircase-, force and block-fct.