Golvvärme - sita 10

Pre-assembled linear manifold with incorporated lockshield valve. Micrometric regulation. Compression ends. Without fittings. Yellow. 2 outlets.

Modules for 1,3,4,6 loops, combineable to max. 12 loops, for connection with basic kit, connection right or left with flat sealing, or connection from below with optional elbowset, supply with lockshield valve for balancing ( with adjusting ring) and shutoff, adjusting ring for balancing without tools, prepared places for room name labels, return with valves and caps, prepared for actuators No.1000138 (24V male) No. 1005605 (230V male) loop connection Q&E 20, Q&E 17 complete with Q&E Rings 1025659,1042836 loop pitch 50 mm header pitch 225 mm max. pressure: 6 bar max. temperature: 60°C material: fibre glass reinforced polyamide

Used on Roth manifold

Uponor Smatrix Wave slave module M-160

Wireless room thermostat in black with display with integrated measurement of relative humidity.

Heat shrink kit connection and end seal JLP for cold cable connection to ETL-10 self.reg. cable

Salus cirkulation pump, A+Rated, 6m, 130 mm

Complete shunt

For those who want to extend the wireless signal range.

Used for floorheating systems

Sparepart for Roth shunt

Brass end coupling male x female x female. For linear manifolds series 7000PM, 7035M, 7035TEM and 7035DM. Yellow.

Complete manifold system, in- and outlet, incl. brackets, 20 mm fittings and end pieces. 12 outlets.

Complete manifold system, in- and outlet, incl. brackets, 20 mm fittings and end pieces. 5 outlets.

Pre-assembled linear manifold with micrometric manoeuvre, with thermostatic option or electrical control, for return pipes. Compression ends. Without fittings. 3 outlets.

Complete adapting set made of brass alloy for polyethylene pipes. Yellow

Fittting for Roth pipe and manifold

Extension to 1" manifold, 2 circuits. 1" manifold, supply and return bar, incl. coupling. Incl. 20/16 fittings.

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

Danfoss SSM underfloor heating manifold in stainless steel with output for 4 heating circuits. SSM floor heating manifolds are equipped with integrated vents and filling/draining function on both flow and return manifold. Manifold SSM is used for heat control in underfloor heating systems. Each hose in the underfloor heating system is connected to the manifold, which makes it possible to regulate the heat supply to all rooms in the building independently. The manifold consists of a flow manifold and a return manifold. The flow manifold allows you to close each circuit independently. The manifold is without a built-in flowmeter. The return manifold is equipped with Danfoss' preset valves, which ensures optimal water balance in the system. The manifold valves can be controlled electronically using thermo actuators. The manifold is available in modules from 2-12 heating circuits. In addition, there are fittings that allow the manifolds to be combined in series - up to a maximum of 16 heating circuits. Ball valves are offered as an option for shutdown between the manifold and the rest of the system.

Danfoss SSM underfloor heating manifold in stainless steel with output for 9 heating circuits. SSM floor heating manifolds are equipped with integrated vents and filling/draining function on both flow and return manifold. Manifold SSM is used for heat control in underfloor heating systems. Each hose in the underfloor heating system is connected to the manifold, which makes it possible to regulate the heat supply to all rooms in the building independently. The manifold consists of a flow manifold and a return manifold. The flow manifold allows you to close each circuit independently. The manifold is without a built-in flowmeter. The return manifold is equipped with Danfoss' preset valves, which ensures optimal water balance in the system. The manifold valves can be controlled electronically using thermo actuators. The manifold is available in modules from 2-12 heating circuits. In addition, there are fittings that allow the manifolds to be combined in series - up to a maximum of 16 heating circuits. Ball valves are offered as an option for shutdown between the manifold and the rest of the system.

Complete insulation for Roth shuntunit

For 1 and 1 1/4 WGF manifolds.

Complete underfloor heating package with shunt, control unit, room thermostats and thermal actuators and 20 mm couplings.

The rotary knob thermostat is a cost-effective room thermostat with simple operation and with all the advanced features of the Danfoss Icon underfloor heating system. Wireless, 3 years battery life, option for limiting temperature setting range, 2 pcs. AA batteries.