PE terminal with screw connection, must be installed on the terminal carrier in MISTRAL panelboard, 9x16mm2 + 12x25mm2

AU3.2 Mounting box The mounting box is designed for installation in all new buildings and in prefabricated building elements, and can be used with cast materials. It has a total of five knock-out inlets, two of which are on the same side. The bottom of the box provides access for two rear inlets. The boxes can be connected to each other with the PMR474 interconnector. Made of halogen free material (IEC/61249-2-21) and fulfills the requirements of the glow wire test according to the standard IEC/EN60670: 2005 (850 °C).

Selector type handle. Indication I-O and ON-OFF. No separate shaft needed. Padlockable with max. 3 padlocks, IP 65, hole distance 36/48 mm, NEMA 1, 3R, 12, red-yellow, OT16...125FT

Terminal shroud for OT16...40F3, -FT3, 3-pole shroud, transparent.

The ESB63..N installation contactors are used to control single and three-phase loads up to 40 A and can be operated by AC or DC voltages. These contactors are made for use in household applications as well as in industrial environments.The following benefits are provided: Hum-free operation, low power consumption and integrated overvoltage protection. Various contact combinations and accessories are available.

Shaft for selector type handle.

The ESB20..N installation contactors are used to control single loads up to 20 A and can be operated by AC or DC voltages. These contactors are made for use in household applications as well as in industrial environments.The following benefits are provided: Hum-free operation, low power consumption and integrated overvoltage protection. Various contact combinations and accessories are available.

Auxiliary Contact Block for AF-contactors

Auxiliary Contact Block for AF-contactors

The ESB25..N installation contactors are used to control single and three-phase loads up to 25 A and can be operated by AC or DC voltages. These contactors are made for use in household applications as well as in industrial environments.The following benefits are provided: Hum-free operation, low power consumption and integrated overvoltage protection. Various contact combinations and accessories are available.

Safety switch 36A 3Poles Red handle IP65 exclusively for LM.

PK67 Mounting plate steel 2CEA000042R0154 from ABB A/S

ABB Fuses switch disconnector

Plug, earthing sleeve position 6h, rated current 125A, IP67 watertight, 3-poles+neutral+earth, frequency 50-60 Hz, color code Red

Plastic enclosed EMC-safety switch, IP 65, includes N- and PE-terminals, black selector-type handle (I-O, ON-OFF indication), padlockable with 3 padlocks in O-position, and auxiliary contacts. Cable entries from top and bottom.

CP4 Roof 2CEA000042L2721 from ABB A/S

Accesories for switch

ABB 1SPE007713F0550 elskåp Blå, Orange

Handle and shaft must be ordered separatly.

Front operated switch-disconnector. Types OT 16...125 include protected terminal clamps, IP 20.

ABB KNX IP router connects the KNX bus with the Ethernet network. The device uses the KNXnet/IP protocol for communication (Routing and Tunneling).It can be used as a fast line and area coupler. The full filter table for main groups 0-31 is supported.KNX devices can be programmed via the LAN using ETS. For this and further clients 5 Tunneling Server are available.DIN 90X36X64 mm (H x W x D)The IP address can be fixed or can be received from a DHCP server. Power supply via 12..30 V DC or PoE.The KNX Standard Communication (Multicast) can be switched off. In this case, up to 10 IPR/S3.1.1 can communicate using unicast communication.

Residual current circuit breaker with overcurrent protection (RCBO) 3P+N. Tripping: A type 13A Rated Residual Current: 300 mA Terminals: 25mm2 Operating temperature: -25C to +55'C Width: 4 modules 71mmTrigger IndicatorIn the event of a ground fault trigger,a blue flag appears on the shift.This feature helpstroubleshooting and reducing downtime.

The RCCBs F200 series assures protection to people and installations against fault current to earth. A large offer for standard instantaneous and selective AC and A types is completed with some configurations for special applications.

IP 65, includes N- and PE-terminals, black selector-type handle (I-O, ON-OFF indication), padlockable with 3 padlocks in O-position, and auxiliary contacts. Knock-out flanges, flanges have to be ordered separately. Normal cable entries can be used.

The B6-30-10 mini contactor is a compact 3 pole contactor with 1 auxiliary contact and screw terminals. They are ideally suited for applications where reliability is a must and space is at a premium. Mini contactors are used in residential buldings, commercial buildings and industrial applications for the control of single or three-phase loads up to 4 kW (AC-3) and 20 A / 690 V (AC-1) or switching of control signals. Further features are the silent coil, a switch position indication and the integrated possibility for rail or wall mounting.