Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Coupling- gunmetal- Rp-threadRp: 2

Viega 3241

Profipress G Coupling with SC-Contur- copper - press connectors Components HNBR sealing elements d: 42

Pipe odour trap - for sink - plastic Components Drain elbow 45°, 2 waste water hose connection Quality controlled in accordance with DIN EN 274

Viega 1613

Waterproof connection socket for flexible Polybutene.- not suitable for PE-X/AI/PE-X, PE-Xc- gunmetal- Rp-thread- soundproofingWith angle in gunmetal, pressure test nozzleModel 5330

Sanpress Inox Reducer with SC-Contur- steel non-corroding- plug-in end, press connectionComponentsEPDM sealing elementd1: 18, d2: 15

Raxofix T-piece with SC-Contur- silicium bronze- press connectors, Rp-threadd1: 20, Rp: 12, d2: 20

Viega 2316.1

Viega 2215.5

Viega 1117.2

Viega 1112

Raxofix Adapter with SC-Contur- silicium bronze- press connection, R-threadd: 16, R: 12

Raxofix Coupling with SC-Contur- Silicium bronze - press connection d1: 25, d2: 25

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Long nipple in gunmetal with R-thread. R: 1, L: 150 mm

Viega 2416.1

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 25, d2: 25, d3: 16

Viega 3121

Viega 2615

Viega 3090

Viega 2415

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Adapter - gunmetal - soldered connection, R-threadd: 15, R: 34