Sanpress Reducer with SC-Contur- gunmetal or silicium bronze- plug-in end, press connectionComponentsEPDM sealing elementd1: 35, d2: 28

Viega 2218

Nipple pipe- gunmetal- G-thread.

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Screw fitting- gunmetal or silicon bronze- R-thread, Rp-thread- flat sealing, angled

Profipress Cap with SC-Contur- copper - press connection Components EPDM sealing elements

Prestabo Sliding coupling with SC-Contur - galvanised non-alloyed steel - press connectors Components EPDM sealing elementsd: 42(VdS certification)

Universal valve with stainless steel valve upper part, with plug, plastic valve lower part, silver-coloured.

Viega Blok 12 mm x 1/2" with bent back pad. For solder connection, insertion dimension. 150 mm, with short redware angles, with bent holder.

Viega Sanpress overbøjning 22 Stainless steel / polished

Connection elbow 90° - for WC - plastic Components - lip seal, additional connectionDN1: 100, L: 230, DN2: 50, version: alpine white

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Smartloop Connection set- for hot water riser pipe with internal circulation pipe, hot water riser pipe from d28, circulation pipe d15- suitable for Smartloop Pipe PB 2007.3- gunmetal or silicium bronzeComponentsPlug, connection socketd1: 28/35, d2: 12

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Connection screw fitting- gunmetal- R-thread, G-thread- flat sealingComponentsPolygon, flat seal AFM 34

Easytop Ball valve- Inlet/outlet: Rp-threadComponentsValve casing gunmetal or silicium bronze according to DIN 50930-6 / DIN EN 1982, maintenance-free selector shaft, stainless steel ball, actuation lever T-form with medium marking green/red exchangeable. Technical dataoperating pressure max. 1.6 MPa (PN 16)operating temperature max. 110 °Cwith DVGW-test markDN: 25, Rp: 1

Rosette - for WC connection elbow, WC connection pipe - plastic DN: 100, Ø: 165, H: 50, version: alpine white

Viega 2318

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon d: 15, R: 12

Viega 2212

Viega 3130

Viega 1126.1

Viega 1117.2

Prestabo connection screw fitting with SC-Contur- galvanised, non-alloyed steel- press connection, G-thread- flat sealingComponentsEPDM flat seal, EPDM sealing element, polygon