Horizontal drain, Ø 75 mm.

Including removable water trap that can be dismantled for cleaning.

Can be rotated 180° if a rearfacing outlet is required. Is 18 mm higher than 1411.0075 and can be used for installation in joist structures.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

Pedal bin with soft open/close lid, non-slip rubber ring at the bottom and specially designed pedal to ensure stability during use. The lid design prevents it from hitting the wall when opened. Removable insert with double-sided tape makes it easy to fit binbags inside. The bin’s mechanical parts are all on the inside, facilitating easy cleaning. A roll of binbags included. Volume 4 l.

The replaceable inner container for the Reframe Collection Toilet brush ensures the most practical and hygienic solution for your bathroom. The plastic container has an external handle which ensures that you can empty the container of water without coming into contact with bacteria.

10-mm tempered glass.The surface is treated with GEWE-clean® nanotechnology, so that the shower screen can be right- or left-aligned.No visible screws and fittings in the finished result.The solution fits tile thicknesses up to 15 mm for wall tiles and up to 20 mm for floor tiles.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 2 different ways:
– If the water trap is positioned at the top and the two side spigots are used for an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the unit connected to the side spigots will be covered by the included water trap, so there is no need for an external water trap.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

Ø 32-mm horizontal drain.

Excluding odour barrier/water trap.

Can be turned in all directions, to simplify pipework.

Cannot be used with any type of water trap. Can only be used as a secondary drain.

The soap dispenser has a sturdy and elegant wall mounting. The design of the pump top ensures liquid soap is released wherever the pressure is applied. Oblique soap dispenser. The entire pump top can be removed to allow for cleaning and refilling. Instructions, screws and dowels are included. Content: 200 ml.

Pedal bin with soft open/close lid, non-slip rubber ring at the bottom and specially designed pedal to ensure stability during use. The lid design prevents it from hitting the wall when opened. Removable insert with double-sided tape makes it easy to fit binbags inside. The bin’s mechanical parts are all on the inside, facilitating easy cleaning. A roll of binbags included. Volume 4 l.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.