Pumpar - sita 3

Groundwater pump KS 2A-1TIL submersible.

MAGNA3 40-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Mobile product for hydronic balancing of radiators in combination with an ALPHA3 pump and a smart phone with the “Go Balance"-app installed, which is available for iOS and Android devices.For temporarily mounting on the ALPHA3 pu

ALPHA2 is able to withstand the tough conditions in a heating system, and with four newly added features, it just got even tougher:Robust start-up:Shakes free any impurities before the pump starts at the beginning of the heating season.Summer mode:Adjustment of the pump’s performance in the summer to the warmer temperature outside – giving customers extra energy efficiency.Magnetite resistance:Ensures that no small pieces of metal get stuck in the pump’s vital parts when they are magnetised.Dry-running protection:Makes sure the pump never runs without liquid in the system - add to that unrivalled energy efficiency, easy installation and the fact that ALPHA2 covers both your heating demands and up to 90 % of your air-conditioning and cooling demands.The GRUNDFOS ALPHA2 is suitable for:• Systems with constant or varying flow• One pipe systems• Two pipe systems• Underfloor-heating• Domestic hot-water recirculation• Systems where night setback is required.Features and benefits• Better performance with market leading efficiency (EEI0.15) in a more compact design• New flow meter for trouble-shooting and balancing• AUTOADAPT selects best performance curve for efficiency and comfort• Innovative plug simplifies pump connection• Insulation shells included.

Pump Ecowatt 1*230V

SOLOLIFT2 D-2Sololift2 D-2 is a small, compact automatic lifting station suitable for pumping of wastewater off places in private dwellings where greywater (w/o faeces) cannot be led directly to the sewer by means of a natural downward slope.Sololift2 D-2 is typically used for:• cabinet showers, washbasins or bidets in basements below sewer level, in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.Sololift2 D-2 is suitable for confined space conditions in built-in cabinets or also below shower receptors or pedestals.The pumping of liquids containing other material may cause faults and limit the scope of our guarantee.The compact lifting station is equipped with- Cable with or without plug (see technical data)- Disc

Vacuum pump that is perfect for heat pump and air conditioning installations.

The UPM3 Hybrid pump is typically used in underfloor or district heating. This UPM3 Hybrid is a spare part that can be used as a replacement for other Grundfos UPM3 variants. However, there may be specially designed pump houses in the UPM3 portfolio where the pump head does not fit. But these pump houses will not be found in typical district heating units, underfloor heating shunts and the like. The UPM3 PH Hybrid contains all the settings and therefore covers all UPM3 product variants. The Quick Guide in the product packaging illustrates the different settings. The UPM3 PH Hybrid also provides control via external signal: PHW and heat. This is performance based on a 7 m variant, but by changing the setting of the pump you can achieve the max curve of 4 m, 5 m and 6 m pump variants.

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

The premium choice when system control and monitoring is key. The MAGNA3 supports fieldbus by optional CIM modules and has a TFT display for intuitive configuration of the intelligent features.Applications:HeatingAir-conditioningPump designs:Canned RotorTechnical data:Head max: 18.88 mLiquid temperature: -10 .. 110 °CMax flow: 76.6 m3/hp max: 16 bar

GRUNDFOS GO MI301The Grundfos GO Remote is used to establish wireless connection to a Grundfos product, using a standard Android or iOS platform, with the Grundfos GO Remote App installed. The App is available from Apple App Store and Google Play free of charge.The MI 301 is a module with built-in infrared and radio communication. It must be used in conjunction with an Android or iOS-based Smartphone with Bluetooth connection. The MI 301 module has rechargeable Li-ion battery and must be charged separately.The pump/system can be monitoried and controlled from the Grundfos GO, and it will be possible to create pdf reports. The specific functions available depend on each individual product.Supplied with the product•Grundfos MI 301•Battery charger•Quickguide.Installation:Range of ambient temperature:70 .. -20 °CRelative humidity:95 %Electrical data:Maximum current consumption:0.03 AEnclosure class (IEC 34-5):IP40

Smedegaard Simflex 25-40 1x230V 180 mm circulation pump 112.

Smedegaard Simflex 25-40 1x230V 130 mm circulation pump 112.

SOLOLIFT2 WC-3Sololift2 WC-3 is a small, compact automatic lifting station suitable for pumping of wastewater off places in private dwellings where wastewater cannot be led directly to the sewer by means of a natural downward slope.Sololift2 WC-3 is suitable for pumping wastewater from a toilet containing toilet paper and faeces with additional connections on the lid and to the sides of the tank for e.g. washbasin, shower or bidet.The pumping of liquids containing other material may cause faults and limit the scope of guarantee.Sololift2 WC-3 is typically used to dewater:• toilet, washbasin, shower and bidet in basements below sewer level,in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.The compact lifting station

Pump Ecowatt U 1*230V

Unilift AP35B.50.06.1.VSubmersible effluent pumpVertical single-stage stainless steel submersiblepump with integrated submersible 1-phasemotor. The pump is fitted with ring stand and carryinghandle and is supplied with a 10 m mainscable. The impeller is a VORTEX impeller for35 mm free passage suitable for pumpingsurface water, groundwater, wastewater andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil. The motor is insulation class F with thermaloverload protection and has long-life deep-groovegreased-for-life ball bearings.The pump has R 2' discharge port and isready for installation either free-standing oron an auto-coupling system.Liquid:Maximum liquid temperature:40 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:R 2'Maximum installation depth:7 mElectrical data:Type of motor:PSCPower input - P1:1 kWRated voltage:1 x 230 VRated current:4.6 ACos phi - power factor:0,98Rated speed:2810 rpmCapacitor size - run:16 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug:SCHUKOOthers:Net weight:9.82 kg

MAGNA3 65-150 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

15-14 BX PMThe high efficiency Coomfort PM range is a product for domestic hotwater recirculation in 1 and 2 family houses.The motor is a single-phase, 2-pole, hysteresis, permanent-magnet motor in conformity with the EMCdirective.Characteristics and benefits:* Unique AUTOADAPT saves up to 50% heatenergy and 87% motor energy compared with a standard pump in continuous operation* Flushing function* Automatic legionella operation (if supported from the system)* Automatic weekend and vacation function* Temperature control optional* Continuous operation optional* Fast and simple electrical installation due to the million times trusted ALPHA plug* Easy to clean and lime insensitive spheric rotor* Application area up 14°dH water hardness* Wearless operation due to liquid lubricated bearing* No leakage risk due to a static seal* Easy maintenance and cleaning by easy-to-separated motor head that fits on all standard circulation pump housings* Korrosion resistant pump housing in brass* Due to impedance protected motor no motor protection necessary* No additional installation costs due to integrated non return and stop valve in the pump housingLiquid:Liquid temperature range:2 .. 95 °CTechnical:TF class:95Approvals on nameplate:VDE,GS,CEMaterials:Pump housing:Brass MS 68Impeller:Stainless steel, EPDM, PPO, PTFE, GraphitInstallation:Maximum operating pressure:10 barPipe connection:G 1 1/4Port-to-port length:110 mmElectrical data:Max. power input:8 WRated voltage:1 x 230 VCurrent in speed 3:0.07 ACapacitor size - run:0.6 FEnclosure class (IEC 34-5):IP44Insulation class (IEC 85):FOthers:Net weight:1.35 kgGross weight:1.51 kgShipping volume:0.003 m3

Salus EP Electronic A-class circulation pump for heating systems and other non-corrosive liquids, ensuring high comfort and low energy consumption.The EP circulation pump is mainly used for water circulation in home heating, and is best suited for the following system:• Stable heating system with variable flow• Heating system with variable pipeline temperature• Industrial circulation system• House and apartment heating systemsThe EP circulation pump can adjust the electric pump's performance automatically and continuously to meet the actual needs of the systemThe EP circulation pump is equipped with a control panel on the front, which is convenient for users. Easy installation and startupEP circulation pump has automatic adaptation mode AUTO (factory setting). In most cases, you can start the pump without making any adjustments and let it automatically adjust to meet the actual needs of the system. High comfortThe operating noise of the pump is low. Low energy consumptionCompared to the conventional circulation pump, its energy consumption is very low. The minimum energy consumption for the EP circulation pump can reach 5 W.EP circulation pump does not need external motor protection. Check whether the voltage and frequency of the power supply correspond to the parameters indicated on the pump nameplate. Use the pump's corresponding connector to connect the power supply (EPPLUG).

MAGNA3 50-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-80 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

Hushållsvattenverkspump levererar 1300 W effekt med upp till 4.8 bar tryck och 4500 l/t kapacitet för automatisk vattenförsörjning, trädgårdsbevattning och pumpning av klart vatten.

Metabo HWW 4500/25 INOX är byggd för energisnål, låg bullernivå vid vattenförsörjning med en tryckbehållare och en tankmonterad tryckströmbrytare som aktiveras automatiskt när vattenbehovet ökar.

• Underhållsfri kondensatormotor med överlastskydd mot överhettning
• Robust pumphus i rostfritt stål och högkvalitativt glidtätningssystem för lång livslängd
• Separat vattenpåfyllningsöppning för enkel användning
• Verktygslöst avtagbar avtappningsplugg för frostskydd
• Lämplig för trädgårdsbevattning med 1 till 3 sprinklers
• Konstruerad för enfas växelström

Pålitligt, automatiskt tryck och flöde gör den dagliga vattenförsörjningen och bevattningen mer bekväm och jämn.

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot