Dräneringsprodukter - sita 22

AMAX Pro, is a drain in PP for drainage systems in buildings for transporting sewage.

AMAX Pro, is a drain in PP for drainage systems in buildings for transporting sewage.

Pieces of PEH for welding, are used for wastewater installations. With TPE sound attenuation.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Geberit Pluvia roof outlet with fastening flange, for roof foils: Maximum discharge rate=12l/s

Geberit Pluvia roof outlet: Maximum discharge rate=9l/s

Drain bowl minimax low model 50 mm.

Wear jo-flex for 153451.

For PP-, PE or PVC-pipe, with link to MA-pipes or MA pipe portion with JET®-link.

For PP-, PE or PVC-pipe, with link to MA-pipes or MA pipe portion with JET®-link.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

The Wafix PP system is made from the reusable PP (Polypropylene), which gives both pipes and fittings good physical and chemical properties. The PP material used has a high E-module, which gives the pipes a good length stiffness and a great impact strength. Therefore, the Wafix PP system withstands the impacts and shocks that can occur during installation and operation - even at minus degrees. Wafix PP is a complete drainage system with pipes and fittings in the dimensions: Ø32 mm Ø40 mm Ø50 mm Ø50 mm Ø75 mm Ø110 mm The program also comes in a white version in dimensions Ø32, Ø40 and Ø50 mm, especially suitable for visible installations. The system's unique Fix·lock® sealing ring seals on as many as three points, providing a large construction surface against the pipe and ensuring that your joints are 100% dense each time. It provides extra security and security if you insert or hide the pipes in a shaft.

The Wafix PP system is made from the reusable PP (Polypropylene), which gives both pipes and fittings good physical and chemical properties. The PP material used has a high E-module, which gives the pipes a good length stiffness and a great impact strength. Therefore, the Wafix PP system withstands the impacts and shocks that can occur during installation and operation - even at minus degrees. Wafix PP is a complete drainage system with pipes and fittings in the dimensions: Ø32 mm Ø40 mm Ø50 mm Ø50 mm Ø75 mm Ø110 mm The program also comes in a white version in dimensions Ø32, Ø40 and Ø50 mm, especially suitable for visible installations. The system's unique Fix·lock® sealing ring seals on as many as three points, providing a large construction surface against the pipe and ensuring that your joints are 100% dense each time. It provides extra security and security if you insert or hide the pipes in a shaft.

dBlue is a drain Pipe in PP (Polypropylene) in 3 layers. It is suitable for installation in locations where there is a requirement for the noise level. The Pipe system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

Wavin BRACKETS 40MM NO LOC DEV WHITE

Pipe clamps for HT PP systems

Grid: 103 x 985 mm. Stainless steel: AISI304/EN1.4301.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

Geberit electrofusion tape for anchor point: D=125 mm,

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 6 mm backwards, to fit 6 – 20mm wall tiles + tile mortar + wetroom membrane.

NB! Only for HighLine Custom frameless.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Wavin PP bend 15° 200mm

Wavin PVC transition 200mm, for concrete sleeve