Dräneringsprodukter - sita 21

For building drainage, For site drainage, For high-tensile, permanent connection of pipes and fittings

For building drainage, For site drainage

dBlue is a drain Fitting in PP-MD (Polypropylene with mineral filler). It is suitable for installation in locations where there is a requirement for the noise level. The Pipe and Fitting system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

dBlue is a drain Pipe in PP (Polypropylene) in 3 layers. It is suitable for installation in locations where there is a requirement for the noise level. The Pipe system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

dBlue is a drain Pipe in PP (Polypropylene) in 3 layers. It is suitable for installation in locations where there is a requirement for the noise level. The Pipe system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

dBlue is a drain Pipe in PP (Polypropylene) in 3 layers. It is suitable for installation in locations where there is a requirement for the noise level. The Pipe system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

Pipe bend Geberit PEH 45° 110X110MM

dBlue is a drain Pipe in PP (Polypropylene) in 3 layers. It is suitable for installation in locations where there is a requirement for the noise level. The Pipe system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

dBlue is a drain Pipe in PP (Polypropylene) in 3 layers. It is suitable for installation in locations where there is a requirement for the noise level. The Pipe system has a proven sound level of 19 dB (A). Is there more stringent requirements for sound, we recommend FRIAPHON.

Reducer pe-hd d110/90 l8 eccentric

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Geberit Pluvia roof outlet with fastening flange, for roof foils: Maximum discharge rate=12l/s

Geberit Pluvia roof outlet: Maximum discharge rate=9l/s

Drain bowl minimax low model 50 mm.

Wear jo-flex for 153451.

For PP-, PE or PVC-pipe, with link to MA-pipes or MA pipe portion with JET®-link.

For PP-, PE or PVC-pipe, with link to MA-pipes or MA pipe portion with JET®-link.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.