Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Smartloop Connection set- for hot water riser pipe with internal circulation pipe, hot water riser pipe from d28, circulation pipe d15- suitable for Smartloop Pipe PB 2007.3- gunmetal or silicium bronzeComponentsPlug, connection socketd1: 35, d2: 12

Long nipple- gunmetal- R-threadR: 12, L: 60

Long nipple- gunmetal- R-threadR: 34, L: 50

Screw fitting- gunmetal- R-thread, Rp-thread- conical sealing

Plug- gunmetal- R-threadComponentsQuadraticR: 1

Plug-in piece - gunmetal - plug-in end, Rp-thread d: 22, Rp: 12

Easytop Slanted seat valve (free-flow valve), with SC-Contur- press connectorsComponentsValve casing and top made of gunmetal or silicium bronze in accordance with DIN 50930-6 / DIN EN 1982, valve seat and valve plate unit stainless steel, spindle transmission, position indication open/closed, ergonomic handwheel and closed with medium marking green/red exchangeable, drain plug G14, EPDM sealing elements.Technical dataoperating pressure max. 1.6 MPa (PN 16)operating temperature max. 90 °Cwith DVGW-test markDN: 25, d: 28

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon d: 22, R: 34

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon d: 18, R: 12

Sanpress T-piece with SC-Contur- gunmetal or silicium bronze- press connectorsComponentsEPDM sealing elementsd1: 22, d2: 15, d3: 22

Viega 2212

Viega 2216.1

Viega 2215.1

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

Viega 2216.1XL

Viega 2215.1

Sanpress T-piece with SC-Contur- gunmetal or silicium bronze- press connectorsComponentsEPDM sealing elements d1: 35, d2: 22, d3: 35

Viega 1118

Pipe clip plastic single for d: 24

Viega 2415

Profipress T-piece with SC-Contur- copper- press connectorsComponentsEPDM sealing elements, VdS certificationd1: 28, d2: 28, d3: 28

T-piece - copper - solder connection d1: 18, d2: 18, d3: 18(quality seal for d12-54)

Viega 2626

Viega 1116XL