Verktyg för VVS-arbete - sita 3

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

Powerful, electric pressure testing pump for pressure and tightness tests of piping systems and receptacles. Testing and pressure range p 60 bar/6 MPa/870 psi. Pumping capacity 6.5 l/min water, hydrous solutions, emulsions, ph-value of liquids 7-10, temperature of liquids 60°C, viscosity of liquids 1.5 mPa s.REMS E-Push 2 – electric charging and testing. Up to 60 bar. With adjustable pressure limiting. 1300 W. Self sucking.

Height-adjustable material support with ball guide for rotating and stationary pipe and rod material. For crafts and industry. For construction sites and workshops. Pipe Ø (1/8) 1 – 6", Ø (6) 25 – 150 mm. Rod material Ø (6) 25 – 150 mm REMS Herkules – the strong support.

Battery 12 V, 2,0 Ah for many pressingsWith use of charger with impulse-tchnology No memory effect

Ridgid rp-219 jaw 19 kn u25

KNIPEX 00 11 06 Universalnyckel för vanliga skåp- och avstängningssystem 90 mm (SB-kort/blister)

KNIPEX 86 09 250 V01 Skyddskäftar för 86 XX 250 3 par

KNIPEX 97 43 200 Crimp-systemtång för utbytbara pressbackar Med flerkomponentsöverdrag brunerat 200 mm

KNIPEX 87 21 250 Cobra® QuickSet Hightech polygriptång med plastöverdrag som ger säkert grepp grå, försedd med korrosionsskydd 250 mm

Specially hardened cutter wheel in approved, tough-hard REMS die-steel quality ensures a long service life.REMS cutter wheel Cu-INOX 3 – 120, s 4Copper tubes, stainless steel tube

Robust quality tools for cutting tubes. Particularly suited for cutting stainless steel tubes.Copper tubes, thin-walled stainless steel tubes, thin-walled steel, aluminium, brass tubes Ø 3 – 28 mm Ø 18 – 118Cutting wheel:4327920515REMS RAS Cu-INOX – for places with difficult access.

Universal quality tool for deburring tubes and edges of different materials. Copper, steel, brass, aluminium, plastic.REMS REG Universal – the all-purpose deburrer.

REMS Sanitol – mineral oil free. Completely water soluable. High lubricating and cooling effect.Synthetic, mineral oil free thread-cutting oil. Specially for drinking water supplies. Also for universal use. For all materials.

Ridgid rp-219 jaw 19 kn u16

RIDGID. 19 kN Press jaw V22 mm profile. Can be used for, among others, Viega Profipress, VSH SudoPress, Conex B-Press and other V press systems. Used in RIDGID RP-219 press machine. Compatible with 19Kn press machines from Rothenberg, Novopress, Milwaukee, Klauke, Geberit, Henco, Vetec and Hilti. Press tray DOES NOT fit with RIDGID's 24 kN press tool.

Deburring for copper tubes and plastic tubes, shaped like a pencil, and is therefore easy to carry in your pocket

Universal internal & external deburrerQuick and easy deburring Ø 4 - 54 mm (1/8 - 1.3/8)with polished cutting blademade of hardened special steel, smooth running. Internal and external deburrer for copper and plastic

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.

KNIPEX 97 61 145 A Presstång för ändhylsor med plastöverdrag 145 mm

KNIPEX 87 03 300 Cobra® Hightech polygriptång med plastöverdrag som ger säkert grepp förkromad 300 mm

KNIPEX 86 03 300 Tångnyckel Tång- och skruvnyckel i ett verktyg med plastöverdrag förkromad 300 mm

KNIPEX 81 13 250 Vattenlås- och kopplingstång med plastöverdrag som ger säkert grepp förkromad 250 mm