Unidrain Dräneringsprodukter - sita 5

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Fit between the drain unit and the outlet unit. Can be used to correct the position of an outlet unit that is too low. 1 x Ø 40-mm side inlet (opened as needed). Not suitable for use with odor barrier 2821.0030.

– If you install water trap 2821.0020 do not turn the side inlet more than 10 degrees away from the center position. Otherwise you will not be able to lift up the water trap for cleaning.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Consists of 4 wooden profiles that are screwed into the wooden joists. The drain unit is inserted into the profile and “clicks” into place.Ensures correct positioning and fixing of the drain unit in wooden floor joist structures. Adjusted to the correct length by cutting the wooden profile.

The vinyl set comprises a magnetic unit, frame and grating. For shower cubicles without fixed walls.

Outlet house, 1412.0075, Ø 75 mm vertical, including trap Product description: Outlet house - line - Ø 75 mm vertical, including trap. The outlet houses have an extra low installation height and large capacity. A locking bracket ensures that the outlet house always sits securely on the drain fitting in the correct position. The trap is included and has a handle on top for easy removal and cleaning.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

Ø 50-mm horizontal drain. Including removable water trap that can be dismantled for cleaning.

Horizontal outlets is located high to obtain low installation height.

Remove the stopper from the selected outlet direction.

Cannot be used as an inlet.

For shower cubicles with open left-hand side, glass screen or similar.

The drain unit has two wall flanges.

Ø 75-mm vertical drain.

Including removable water trap that can be dismantled for cleaning.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.