3M Anslutande utrustning

Thermal shrink tubes

3M HDCW-55/15-250

Scotch® Cable Jacket Repair Tape 2234 has a tough, abrasion-resistant backing, for jacket repair on industrial cables. Flexible and self-healing, the tape keeps out moisture and is 2x6' (50,8 mm x 1,82 m) roll. Key applications include repairing cables in conditions where flexibility, durability, abrasion and notch-resistance, vibration, and chaffing of cables are at a premium target.

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

3MTM Heat Shrink Wraparound Cable Repair Wrap Sleeves HDCW are designed to quickly repair damaged cable jacketing. They may also be used to rejacket in-line splices.

3M Brand PST Cold Shrink Connector Insulators are a series of open-ended, tubular rubber sleeves, which are factory expanded and assembled onto a removable core. They are supplied for field installation in this pre-stretched condition. The core is removed after the tube has been positioned for installation over an in line connection, terminal lug, etc., allowing the tube to shrink and form a waterproof seal. The insulating tube is made of EPDM rubber, which contains no chlorides orsulphurs. Six diameter sizes will cover a range of 1000 volt cables, copper and aluminium conductors.

This splice meets requirements of ANSI C119-1 and Western Underground Guide 2.14 for secondary splices rated up to 1 kV. This size is listed for availability only and is not designed to be used as primary insulation. This tube is for conduit sealing an breakout. Important: Use wire insulation/jacket diameters and connector O.D. for final sizing confirmation.

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

3MTM Heat Shrink Wraparound Cable Repair Wrap Sleeves HDCW are designed to quickly repair damaged cable jacketing. They may also be used to rejacket in-line splices.

Complete heat shrink kit for reperations.

Heat shrinkable end caps are typicallyused to seal cable ends and providemechanical and environmentalprotection. With the exception of SKE4/10, these end caps can be fitted withair valves suitable for pressurized cableapplications. Consult factory.

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

ETW-803 is a flexible heat shrinkable tubing with a co-extruded hot melt adhesive inner wall. The excellent flowproperties of the adhesive ensure good environmental sealing of complex parts. As this tubing shrinks, molten adhesive flows and is forced into gaps and crevices. When the adhesive cools it forms a seal against moisture and other fluids whilst the outer wall provides mechanical protection. ETW-803 is well suited for environmental sealing of a variety of electronic, electrical and mechanical applications such as connections, joints etc. ETW-804 with a shrink ratio of 4 :1 accommodateswide variances in diameter.

Complete shrink sleeve set for cable repair. Contains thermoplastic adhesive that ensures permanent tightness and long durability.

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

ETW-803 is a flexible heat shrinkable tubing with a co-extruded hot melt adhesive inner wall. The excellent flowproperties of the adhesive ensure good environmental sealing of complex parts. As this tubing shrinks, molten adhesive flows and is forced into gaps and crevices. When the adhesive cools it forms a seal against moisture and other fluids whilst the outer wall provides mechanical protection. ETW-803 is well suited for environmental sealing of a variety of electronic, electrical and mechanical applications such as connections, joints etc. ETW-804 with a shrink ratio of 4 : 1 accommodateswide variances in diameter.

ETW-803 is a flexible heat shrinkable tubing with a co-extruded hot melt adhesive inner wall. The excellent flowproperties of the adhesive ensure good environmental sealing of complex parts. As this tubing shrinks, molten adhesive flows and is forced into gaps and crevices. When the adhesive cools it forms a seal against moisture and other fluids whilst the outer wall provides mechanical protection. ETW-803 is well suited for environmental sealing of a variety of electronic, electrical and mechanical applications such as connections, joints etc. ETW-804 with a shrink ratio of 4 : 1 accommodateswide variances in diameter.

The HDCW Wraparound Heat Shrink Cable RepairSleeve is designed to repair damaged cable sheaths. It isalso suitable for use with cable joints and as additionalcorrosion protection on undamaged cables.Quick and easy to apply, it provides maximumprotection against mechanical stress, even in the mostaggressive environments. The inner wall of the sleeve iscoated with hot melt adhesive to achieve a safe andwatertight bond with the cable and give a perfect sealwhen heat is applied, while a corrosion proof metal clipis used to fully close the sleeve.Heat shrinkable Cable Repair Sleeves are available in arange of sizes to fit cable diameters from 10 - 140mmand in four lengths from 250 – 1000mm

3M Brand PST Cold Shrink Connector Insulators are a series of open-ended, tubular rubber sleeves, which are factory expanded and assembled onto a removable core. They are supplied for field installation in this pre-stretched condition. The core is removed after the tube has been positioned for installation over an in line connection, terminal lug, etc., allowing the tube to shrink and form a waterproof seal. The insulating tube is made of EPDM rubber, which contains no chlorides or sulphurs. Six diameter sizes will cover a range of 1000 volt cables, copper and aluminium conductors.

3M Super 88 1 styck

MDT-AF is a mediumwall Polyolefin heatshrink tubing with hot melt adhesive. Shrink ratio is up to 4:1, min. shrink temperature is 135°C, operating temperature is -55°C to +130°C. Flame retardant - self extinguishing. Good chemical resistance. IP 68 sealing

Thermal shrink tubes

Thermal shrink tubes